氣體吸附式干澀機

◆物品特征 Product features

※享有安全不一的撒氣氣壓和露點

1.吸收塔之非常與直勁經試驗可是高精密計算，塔床摩擦阻力小，做到了解壓縮氣物潮濕劑5秒的排斥時候，考慮半成品氣的露點的標準。

2.30％的干躁劑剩余，采用補償金干躁劑的生態老化試驗，保證干躁。

3.特大型傳播器，切實保障氣體勻經由空氣干燥劑層，清理溝流不良現象。

※降解氣量耗損率少于14％

1.優秀的機筒設計的概念，存為100％的吸出熱能量，永久保存的熱能量于增大凈化階段中，的凈化氣溫暖，增長設施設備的解吸學習能力，可使得凈化更全面。

2.干躁和再造采取返向對流傳熱方案范文，濕水汽穿過干的吸附劑劑限期果較好。再造氣出來含濕量調整在亞趨于穩定睡眠狀態，使消音器及進氣車道無結水之慮。

3.可據干燥處理機的工作電動機扭矩實際需求調節器復蘇氣運用量，保障復蘇氣團不斷安穩，復蘇負壓低至臨介。

※干澀劑應用平均壽命更長久

1.適合的機筒長寬比，使氣體憑借晾干劑層的水流量和日子始終維持好的情況下，多方面起晾干劑的使用性能。

2.合情合理的控制系統分配，在氣體開啟機筒前，經除油處里有效清理氣體中內動植物油物與重破壞物，杜絕常溫、干燥劑層受破壞。

※裝備按照了先進高產品質量電動三輪及手動閥和牢靠的全電子為了滿足電子時代發展的需求，可語言編程序調整器，人與機器游戲界面和睦，系統自動反復表示雙塔工程，反復的周期實地可編，出廠日期控制10min。銅閥壽命短短短50萬次操作。

※筒節側壁作冷鍍鋅鋼板除銹治理 ，10年不氧化。

※小動作最準、性能方面固定、進行操作簡便計算，進行安裝不能自己理論知識。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆重點方法產品參數 Main technical parameters